GENIUS CNC machining trick that all machinists can use to prevent breaking tools in dynamic milling toolpaths using Mastercam on the DN Solutions BVM 5700
#cncmachine #machining #engineering
#fabrication 3d printer 5-axis 5th axis additive additive manufacturing Bicycling Bicycling UK Bicycling United Kingdom Biking Biking UK Biking United Kingdom CAD cam cnc cnc lathe cnc machine cnc machining cnc machinist cnc mill cnc milling machine cnc operator Computer Numerical Control Cycling Cycling Colchester UK cycling uk Cycling United Kingdom DN Solutions Doosan drill drilling edm engineer engineering Kennametal Lathe machine machine operator Machine Shop machining machinist manufacturing Metal Metalworking mill mill turn milling multiaxis operator steel swiss lathe Swiss machine Swiss machining UK united kingdom
35 Comments
I thought you were milling a post. If all you wanted to do was mill the entire surface, why wouldn't you just mill it back and forth? Genuine question; I don't know much about machining.
In the first way it was also possible to do the same. Both ways of wasting metal are good
๐น๐น๐น๐น
Another great way? Cut the material to length first ๐
"im Dr Steve Brule, for yur health๐๐ป"
The internal hose on a taper isn't it ?
What's the point? Just saw it off before milling.
Start with a shorter block.
just drill a hole
Iโve never seen but just watching the beginning it hurts my soul
Cut off saw.
What is this machine strategy name. Like roughing from out side and move inside.
What mining of this job pice facing๐๐ (time pass) realy?
Nice
I'm smarter now
Iโm not any pro at this itโs just a question, can you just go inside out?
What is point of this video ?why are you doing this kind of phase tool like that ??
ะกะฒะตัะปะพะผ ะฝะต ััะดัะฑะฐ ััะพ ะดะตะปะฐัั? ะฃะฑะธะฒะฐะตััั ะธะฝััััะผะตะฝั ัะฐะบะธะผ ะพะฑัะฐะทะพะผ! ะะพะถะฝะพ ะดััะณะพะน ัััะฐัะตะณะธะตะน ะพะฑัะฐะฑะฐััะฒะฐัั. ะัะตะดะฝัะต ัะพะฒะตัั ัะฐะทะดะฐััะต…
Ramp down > and outter milling???
Why!!!!!!!! You can start to mill at inner hole which is you made!
I know why they make this video,
Sometimes someone should do this job like idiot by weak and not rigid machine.
Even they can't consider 'face cutter'
Because the machine is so weak.
I hope they want to explain about that.
Anyway. I can't agree about that,
Why he didn't use the center hole he made by ramping down for milling top stock….
I can't stand their side.. what was the purpose …..
This os the third fucking time I've seen this video, from three different channels.
Why is the first method wrong?
Es mรกs fรกcil cortar el trozo de metal a la medida y ya solo darle el acabado y dimensiรณn final en la CNC con un menor desperdicio de metal y herramienta. Pero a los gringos les gusta ser muy complicados. ๐๐๐
Why tf would you remove that much material on a CNC mill? Just cut it, then machine it
Try bandsaw instead of turning inches of steel into chips
this is an issue that doesn't exists
๐
Question, is the cut off metal recycled or does it all go to waste and new metal is mined?
Or just use the right tool for the job lol like an actual 6 to 8 inch face mill and run a better pattern.
Why not just have the stock cut to the appropriate length to begin with?
You could also drill a hole in the center of that before you start milling.
Or just raster it
the schunk advertisement is lame ๐
This is why i use my big face mill
Isnt it easier to use a band saw?
์๋๋ฐ ์๊น์ฐ๋๊น ๋๋ฆด๊ตฌ๋ฉ์ ํ๋ ๋ซ์ด๋๋๊ฒ ๋…